By Plumbing Guide for Installing a Bathtub
By Plumbing Guide for Installing a Bathtub
Blog Article
This post following next on the subject of How to Install a Bathtub is pretty much interesting. You should give it a look.
Setting up a bath tub isn't exactly brain surgery, yet it does call for solid plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a new one is also a moderately hard project. If the old tub is easily available, the task can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and also position the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have certified on your own for the task and fit attempting it. As opposed to employing a service provider to take over a halfway-completed project, it is far better to think about using one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This short article will certainly aid you install a new bathtub in your restroom if you have actually already purchased a new bathtub and also don't require to change the arrangement of your previous supply of water pipelines.
Your tools and also material list ought to comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing faucets can be quite bothersome because of the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in place between the tap as well as the sink. Secure the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The previous kind ought to be attached to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Making use of both wood boards under its feet, place the bath tub in the required position. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub up until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest adaptable tap port to the proper supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water supply and check all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow outlet and the typical electrical outlet for leaks.
Finally, repair the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the tub must wait till the tub has been used at the very least when as this will certainly settle it right into its final position.
Planning for the Installation
To start with, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can break relatively early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is advisable to fit the tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads on How to Install a Bathtub, I figured sharing that piece of content was beneficial. So long as you enjoyed our blog entry please remember to share it. Thank you for going through it.
Reliable? That's us! Report this page